Tuesday, December 14, 2010

Birdhouses from Greeting Cards

Photobucket

After I had made the greeting card village ornaments I decided that I wanted to make some birdhouse ones. Since the angles for these ones were not as straight forward I couldn't just score the patterns directly on the greeting cards. I made patterns with graph paper first.

If you'd like a pdf version of the pattern for my birdhouses you can click this link. (If you don't have access to a printer you can consult the pattern to draw your own. I drew the four sections of the house on 1/4 inch graph paper and then taped them together.)

After I had made the pattern I taped it to the back of the greeting card front. (This pattern will fit on any card that is larger than approximately 4 x 6 inches.) I took a sharp pin and poked some holes to indicate where the fold lines and the entrance would be. (One mark near either end of every fold line is sufficient.)

Photobucket

Then I cut around the pattern.

Photobucket

I scored all the fold lines and used a soft pencil to make a line to mark the centre line of the entrance. Then I punched the entrance ...

Photobucket

... creased all the fold lines ...

Photobucket

... and placed a piece of double sided tape on the tab.

Photobucket

I rolled the house, removed the backing from the tape and stuck the tab to the inside of the front wall. (If I had used use glue instead of double sided tape I would have folded up one piece of the base and used something like a clothespin to clamp the tab to the front wall. Alternatively I could have eliminated the tab and used tape, like I did on the greeting card village ornaments.)

Photobucket

Next I assembled one side of the roof. I used double sided tape to attach the adjacent flaps to the roof piece. (Again if I had used use glue I would have used something like a clothespins to clamp the pieces together.)

Photobucket

Then I attached the two remaining flaps to the other side of the roof. (If I had used glue I would have laid this side of the roof down on my work surface until the glue was set.)

Photobucket

Next I assembled the base. I folded up the two rectangular pieces then used double sided tape to attach the other two pieces of the base. I inserted the handle of a small paint brush in the punched entrance to press the layers together.

Photobucket

Then I was ready to assemble the outer roof. Because of the simple geometry I could have used my quilt ruler to score the pattern directly onto the back of the card, like I had on the greeting card village ornaments. Instead I taped, marked and cut out the pattern like I had the larger piece of the birdhouse.

Photobucket

I scored the fold lines. Then I folded the hanging thread in half, knotted the two ends together ...

Photobucket

... and used a needle and thread to pull the folded end from the inside to the outside of the roof.

Photobucket

Next I creased the fold lines of the outer roof.

Photobucket

I applied some fast drying glue to one side of the house roof and gently laid it on Side A of the outer roof so that the roof peaks were together and the house was centred. (Side A has the notch at the centre front.) When it was in place I pressed the house against the outer roof. If I had used regular glue I would have left it laying like this until the glue was dry.

Photobucket

Then I applied glue to the other side of the house roof and pressed the remaining half of the outer roof in place. When the roof was in place there was a bit of the trim extending above the roof. I placed a spot of glue between the two pieces of trim on the front and pressed them together. Then I glued the two pieces of trim on the back of the birdhouse together.

Photobucket

When the glue was set I used scissors to carefully cut the trim flat against the roof.

Photobucket

For this birdhouse I decided to add a bit of glitter to the roof. I painted some white glue on the surfaces of the outer roof and then sprinkled the glitter over the roof. When it was dry, and the excess glitter poured back into the container, it looked like this.

Photobucket

Most of the greeting card birdhouses I have made have had colourful (front of the greeting card) walls and a snowy white (back of the greeting card) outer roof. A birdhouse with white walls and a colourful roof can work well too.

Photobucket

At the suggestion of a dear friend I'm going to post a link to a jpg of a scan of my original pattern so that you can scale the pattern to whatever size you desire. You could scale it so both patterns fit on a single sheet of card stock. Or scale it so that the house part fills a single sheet of cardstock and you need a second sheet for the roof. Or ...

http://imageshack.us/photo/my-images/406/birdhousejpg.jpg/

Note. I used the star shaped punch because it was the only one I had that was a good size. If I hadn't had my star punch here are some alternatives I would have tried. Going clockwise the green circle was cut from a greeting card, the small blue circle is a hole made with a regular hole punch, the red star is a sticker and the blue diamond is a hole cut with a mat knife. Another possibility is a 1/2 inch round sticker, which may be found where office supplies are sold.

Photobucket

Photobucket
Pinwheel 2010

2 comments:

  1. These are SO very adorable & clever. I love the pictures on the greeting cards and the glittery roof. And how you used a star punch. TOO cute. Thank You for stopping by my blog & linking these up & thanks for the fabulous inspiration!

    ReplyDelete
  2. Thanks Mel! Your blog page of paper house links, http://melstampz.blogspot.com/2008/09/wee-houses-35-templates-tutorials.html is a fantastic resource.

    ReplyDelete